MOLD SILICONE MOLD STAR 31T 0,91 KG

https://kevytrakentajanverkkokauppa.fi/web/image/product.template/5203/image_1920?unique=4d387d1
(0 review)

Fast-curing silicone for quick and easy silicone mold making. 

Expiration date: November 19, 2026

44,19 € 44.19 EUR 58,91 € VAT Included

(0,00 € / Units)

30 days lowest price 1.56

This combination does not exist.

SILIKONI


Product Information

MOLD STAR 31T 0,91T 

Mold Star™ 31T is a fast-curing, translucent and easy-to-dispense platinum-cure silicone designed for making silicone molds. It features a simple 1A:1B mix ratio by both volume and weight. The pot life is approximately 5 minutes, and the mold can be demolded after approximately 23 minutes when working at room temperature. The cured silicone has a Shore A hardness of 30. Mold Star 31T is ideal for applications where a silicone mold needs to be ready for use quickly. 

A cured Mold Star 31T mold is flexible, has good tear strength and exhibits very low shrinkage. It is suitable for casting materials such as wax, gypsum and resins, as well as for encapsulation applications. With a heat resistance of up to 232 °C, the material can also be used for casting low-melting-point metal alloys. 

Features

  • Cures at room temperature
  • High tear strength
  • High heat resistance
  • Low shrinkage
  • Release agent not required for most applications


Applications

  • Mold making
  • Wax and plaster casting
  • Compatible with most casting resins (urethane, polyester and epoxy)
Hardness (ShoreA)

30

Mix Ratio (by Volume)

1:1

Pot Life (23 °C)

5 min

Cure Time (23 °C)

23 min 

Temperature Resistance (min)

-53 °C

Temperature Resistance (max)

232 °C

Shrinkage

<0.0254 mm/mm

Viscosity (cpc)  

11 000

Elongation (%)

400

Color

 Translucent

Instructions for Use

Thoroughly mix each component separately before use, as the materials may separate during storage. Measure Parts A and B at a ratio of 1:1 by either weight or volume. Mix thoroughly. Scrape the sides and bottom of the mixing container carefully to ensure an even cure.

Vacuum degassing is not necessary for most applications. If desired, the mixture can be vacuum degassed to reduce entrapped air. Use a vacuum pump capable of pulling at least 1 bar of vacuum. Leave sufficient room in the container for the material to expand, as the silicone will expand to several times its original volume. It will rise, break and then fall back down. 

Pour the silicone slowly into the lowest point of the mold and allow it to flow gradually to the desired level. When making a one-piece silicone mold, it is recommended to pour at least 1 cm of silicone above the highest point of the model. 

Allow the mold to cure at room temperature (23 °C) for the recommended time. Do not cure at temperatures below 18 °C, as the curing reaction may slow significantly or fail completely.

Cure inhibition: Certain materials can interfere with the curing of addition-cure silicones, including latex, tin-cure silicones, sulfur-containing clays, certain wood surfaces, freshly cast polyester, epoxy and polyurethane products. If compatibility is uncertain, perform a small test cure first. Cure inhibition is indicated if the silicone remains tacky or fails to cure. Coating the model with a clear acrylic lacquer may help prevent cure inhibition. Allow the coating to dry completely before applying the silicone.

Note: Platinum-cure silicone is not compatible with clays containing high levels of sulfur. 

Mold Use and Storage

A new silicone mold is naturally non-stick, but repeated use, especially with resins, can gradually wear the mold surface. A release agent is generally not required when casting wax or gypsum. When casting polyurethane, polyester or epoxy resins, the use of a suitable release agent is recommended.

Wash the mold with a mild soap solution and dry thoroughly. Assemble multi-part molds before storage. Store the mold on a flat surface in a cool, dry place away from direct sunlight.

Thickening and Thinning the Silicone

  • THI-VEX™ can be used to thicken the silicone, for example when making brush-on molds. Add the required amount until the desired consistency is achieved.
  • Silicone Thinner™ reduces viscosity, making the silicone easier to pour and vacuum degas. Please note that it reduces tear and tensile strength. Do not add more than 10% by weight to the total mixture.
Safety

Use in a well-ventilated area. Safety glasses, long sleeves and vinyl gloves only are recommended. Do not use latex gloves, as latex can inhibit the cure of the silicone. Use and store the material at room temperature (approximately 23 °C). Higher temperatures significantly reduce working and curing times and may also shorten the product's shelf life. Use the product as soon as possible, as it has a limited shelf life. 

Products in our selection

Dynaaminen pätkäsi näytetään tässä... Tämä viesti näytetään, koska et ole antanut sekä suodatinta että mallia käytettäväksi.